RFid click features CR95HF 13.56 MHz contactless transceiver as well as trace antenna. The click is designed to run on a 3.3V power supply only. It communicates with the target MCU via mikroBUS™ UART (TX, RX), SPI (MISO, MOSI, SCK, CS) INT, RST, PWM and AN lines.
Wurth Elektronik EMC / Filter products are ideal to solve all electromagnetic interferences. For example filtering of data, power and communication lines, common and differential noise suppression on wire or PCB.
Accel 3 click carries the H3LIS331DL a low-power high-performance 3-axis linear accelerometer. The click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over SPI or I2C interface, with additional functionality provided by the INT pin on the mikroBUS™ line.
STSPIN220 click is a stepper motor driver with the PWM current control and selectable microstepping up to 256 microsteps. It is based on the STSPIN220, a low voltage stepper motor driver from STSPIN2 series.
Gyro 4 Click is a two-axis MEMS gyroscope for optical image stabilization applications. It is equipped with the L20G20IS, that includes a sensing element and an IC interface capable of providing the measured angular rate to the application through an SPI digital interface.
6DOF IMU 8 click is an advanced 6-axis motion tracking Click board™, which utilizes the ISM330DLC, a high-performance System in Package (SiP), equipped with a 3-axis gyroscope, and a 3-axis accelerometer.
NFC Tag 4 Click is NFC tag device, offering 16 Kbit of electrically erasable programmable memory (EEPROM). This Click Board™ offer two communication interfaces. The first one is an I2C serial link and can be operated from a DC power supply.
AudioMUX click is a sound processing Click board™ with digital controls, based on the TDA7468D IC. It can be used to select one of four audio input channels, adjust its frequency response and volume, and send it to the output.
Barometer 2 Click is a digital barometer on a Click board™. Barometer 2 is equipped with the LPS35HW, an absolute piezoresistive pressure sensor with ceramic, water resistant package, manufactured using a proprietary technology.
3D Hall 3 click is a very accurate, magnetic field sensing Click board™, used to measure the intensity of the magnetic field across three perpendicular axes. It is equipped with the LIS2MDL, a low power 3D magnetic sensor.
VReg click is a digitally controlled DC Voltage regulator in mikroBUS™ form factor. The design is based on the well-known LM317-M circuit, with the addition of a 12-bit DAC, 12-bit ADC, and an Operational Amplifier. Two pairs of screw terminals serve as inputs and outputs.
9DOF click carries ST's LSM9DS1 inertial measurement module that combines a 3D accelerometer, a 3D gyroscope and a 3D magnetometer into a single device outputting so called nine degrees of freedom data.
Charger 2 click is a LiPo/Li-Ion battery charger with the additional monitoring IC onboard. It carries the STBC08, a standalone linear battery charger IC and the STC3100, a battery monitor IC with Coulomb counter/gas gauge.
Develop a cellular connected product with Particle's Electron. In one small package, you can build a connected parking meter, shipping container or agricultural sensor with our integrated offering of cellular hardware.
Small and powerful Wi-Fi connected microcontroller. Based on Cypress's WICED architecture, the Particle Photon Series combines a powerful STM32 ARM Cortex M3 microcontroller and a Cypress Wi-Fi chip. This keeps the footprint small but the function broad.
SPIRIT 2 Click features the SP1ML-915, an ultra-low power, fully integrated RF module, which operates at 915 MHz ISM band. This Click board™ can be used to add wireless connectivity to any application, requiring no extensive RF communication experience.
Maia is a single embedded low cost wireless M-Bus RF Module developed specially for the AMR (Automatic Meter Reading) smart metering and smart grid infrastructure where the Wireless M-Bus standard (EN13757-4) and OMS standards are used.