Door Lock

Key Features

• Immediate evaluation of Voltage Regulators, Power Management and Multichannel Power Management with a selection of samples.
• The kit includes
  • 10 samples

Show More

Key Features

• Compatible with all available ST MEMS adapter boards
• Controlled by the STM32F103RET6 high-performance ARM Cortex^™ -M3 microcontroller
• Includes a DIL24 socket for easy MEMS adapter connection
• 3 V on-board linear voltage regulator
• DFU compatible for USB microprocessor firmware update
• USB 2.0 full-speed compliant
• Debugging connector for SWD/JTAG
• RoHS compliant

Show More

Key Features

• Complete A3G4250D pinout for a standard DIL 24 socket
• Fully compatible with the STEVAL-MKI109V2 motherboard
• RoHS compliant

Show More

Key Features

• Supports both SPC5-UDESTK standalone and the equivalent version embedded into Discovery board.
• Supports SPC5x MCUs
• Supports Multicore, eTPU and GTM debugging
• Includes FLASH programming capability
• Support service provided through STMicroelectronics

Show More

Key Features

• Board Supply: Single 12 VDC external power supply input. Two regulators provide power voltages 5 V and 3.3 V.
• Main power switch and three power supply status LEDs (+12 V, +5 V and +3.3 V)
• All MCU signals accessible by a 37 x 4 100 mil pin grid array allowing connection of an additional board for dedicated applications.
• JTAG interface (7 x 2 male 100 mil connector)
• Two FlexRay channels with jumper enable and DB9 male connector.
• Two CAN channels with jumper enable and DB9 male connector
• K-Line interface.
• Two LIN interfaces (HW configurable)
• Two potentiometers for analog voltage input
• Three user LEDs.
• 40 MHz crystal.
• Reset push button.
• Specification:
  • Board size 115 x 135mm
  • 12 VDC center positive, 2.1 mm inner diameter.

Show More

Key Features

• SPC560P50L5 32-bit 64MHz e200z0h CPU;32-bit Power Architecture^® Technology CPU, 576 KB Flash in an LQFP144 package.
• Shield Connectors (Arduinocompatible).
• On-board USB-JTAG PLS debugger and HW selection mode to use stand-alone JTAG debuggers (2 x 7 male 100mil connector).
• Free 128 Kbyte code size limited debugging
• Board power supply: from the USB bus (5 V supply voltage) or through external +12 V PSU.
• All GPIOs and DSPI/USB signals accessible by a 4x37 100mil pin grid array allowing connection of an additional boards for dedicated applications.
• CAN, K-LINE, LIN, FlexRay interfaces.
• Main power switch.
• Reset push button.
• 2 potentiometers for ADC evaluation
• 12 MHz crystal.
• Board size 152 x 103 mm

Show More

Key Features

• The SPC570S50Ex 32-bit CPU implements two e200z0h processor cores:
  • Core_0 - Main core (80MHz)
  • Core_0s – Checker (safety)
• On-board USB-JTAG PLS debugger and HW selection mode to use it or a third party JTAG debuggers.
• 256 kByte code size limited debugging free of charge evaluation license included.
• Board power supply through the USB bus (5 V supply voltage) or external +12 V PSU.
• User push buttons and LEDs
• Reset button
• 2 potentiometers for ADC evaluation
• Extension headers (4x37 pin - 100 mil) for all device pins and for quick connection to prototyping expansion boards, additional modules and evaluation probing.
• JTAG interface (2x7 male 100mil)
• USB port (mini - B)
• 40 MHz crystal
• Board size 105 x 150mm

Show More

Key Features

• Complete AIS3624DQ pin-out for a standard DIL24 socket
• Fully compatible with STEVAL-MKI109V2 motherboard
• RoHS compliant

Show More

Key Features

• Input voltage 5 V
• 12 V output, step-up converter for transceiver supply voltage
• LIN transceiver
• CAN transceiver
• Automotive-grade ESD protection
• IEC61000-4-2 compatibility

Show More

Key Features

• Compatible with all available ST MEMS adapter boards
• Controlled by the STM32F401VE high-performance ARM Cortex™ - M4 microcontroller
• Software-adjustable power circuitry to set sensor supply voltage from 0 to 3.6 V
• Includes a DIL24 socket for easy MEMS adapter connection
• Adjustable MEMS DIL24 power supply
• DFU-compatible for USB microprocessor firmware update
• USB 2.0 full-speed compliant
• Embedded power monitoring circuitry on sensor supply voltage and current
• Debugging connector for SWD/JTAG
• Can be used with PC software like Unico GUI to manage and analyze MEMS sensor data
• RoHS compliant

Show More

Key Features

• Complete AIS328DQ pinout for a standard DIL 24 socket
• Fully compatible with the STEVAL-MKI109V2 motherboard
• RoHS compliant

Show More