概述
解决方案
硬件评估工具
资源
Tools and Software
主要产品
开始

牲畜是消费者蛋白质和营养的主要来源,其需求在全球范围内逐年增加。为提高效率和生产率,肉类行业希望能够记录每个动物在牧场的位置和活动数据。定位和跟踪应用依赖于通过MEMS运动传感器(用于检测动物移动或位置变化)运作的核心微控制器单元、基于GNSS的专用定位芯片组,以及用于传送所获数据的连接块。

ST可以为各种基于连接、地理定位和运动传感器的动物定位和追踪设备提供完整的解决方案。ST基于低功耗Cortex-M0核心或其超低功耗版本(M0+)的多种STM32微处理器产品组合是能够满足具有挑战的性能和功耗要求的最佳选择。由于定位会消耗大量电力,因此使用ST的低功率加速度计来检测动物何时静止并在动物不活动时关闭电源是一项重要策略。

此外,低功耗RF通信是此应用的关键。ST的产品组合提供了一系列非常适合任何需要的连接解决方案:用于数据记录、动物识别和健康记录的NFC EEPROM;用于与智能手机(用于分析参数)无缝连接的低功耗蓝牙;数据收集和参数设置;用于远程通信的sub-GHz技术。

产品型号
描述
NUCLEO-L073RZ STM32 Nucleo-64 development board with STM32L073RZ MCU, supports Arduino and ST morpho connectivity Quick view

主要特性

  • Common features
    • STM32 microcontroller in LQFP64 package
    • 1 user LED shared with Arduino™
    • 1 user and 1 reset push-buttons
    • 32.768 kHz crystal oscillator
    • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
    • Flexible power-supply options: ST-LINK, USB VBUS or external sources
    • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs
  • Board-specific features
    • External SMPS to generate Vcore logic supply
    • 24 MHz HSE
    • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI® debug connector
    • Arm® Mbed Enabled™ compliant

Show More

STEVAL-ISB033V1 Evaluation board for STBCFG01 single-cell Li+ battery charger with OTG boost, voltage mode fuel gauge and 200 mA LDO Quick view

主要特性

    • 2 MHz or 3 MHz switching frequency
    • 1.2 A max. charging current
    • 20 V tolerant input with OVP
    • Programmable input current limitation and dynamic input current limit
    • Battery overvoltage protection
    • Auto-recharge
    • Integrated current sensing resistor
    • USB compatible
  • Voltage mode fuel gauge
    • External sensing resistor not needed
    • Battery swap detection through ID resistor
    • Low battery voltage and low SOC programmable alarms
  • 50 mA LDO for system boot in dead battery condition
  • USB OTG VBUS generation (500 mA)
    • USB overvoltage protection
    • Programmable battery overcurrent protection
  • Automatic 60 mA input pre-bias
  • I²C compatible control interface
  • Interrupt output pin
  • RoHS compliant

Show More

X-NUCLEO-IDB05A1 Bluetooth Low Energy expansion board based on SPBTLE-RF module for STM32 Nucleo Quick view

主要特性

  • STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo
  • X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF)
  • SPBTLE-RF:
    • Bluetooth Low Energy FCC and IC certified module based on Bluetooth® SMART 4.1 network processor BlueNRG-MS
    • Integrated Balun (BALF-NRG-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • Scalable solution, capable of cascading multiple boards for larger systems
  • Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware
  • RoHS compliant

Show More

STEVAL-ISA189V1 38 V, 1.5 A synchronous step-down switching regulator evaluation board based on A6986F5V Quick view

主要特性

  • AECQ100 qualification
  • 1.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 45 μA IQ at light load (LCM VIN = 12 V)
  • 8 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Fixed output voltage VOUT = 5 V
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

STEVAL-ISA185V1 38 V, 0.5 A synchronous step-down switching regulator evaluation board based on A6985F3V3 Quick view

主要特性

  • AECQ100 qualification
  • 0.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 30 μA IQ at light load (LCM VIN = 12 V)
  • 8 μA IQ -SHTDWN
  • Adjustable f SW (250 kHz - 2 MHz)
  • Fixed output voltage VOUT = 3.3 V
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 360 mΩ ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

STEVAL-ISA186V1 38 V, 0.5 A synchronous step-down switching regulator evaluation board based on A6985F5V Quick view

主要特性

  • AECQ100 qualification
  • 0.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 45 μA IQ at light load (LCM VIN = 12 V)
  • 8 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Fixed output voltage VOUT = 5 V
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 360 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

STEVAL-ISA187V1 38 V, 0.5 A synchronous step-down switching regulator evaluation board based on A6985F Quick view

主要特性

  • AECQ100 qualification
  • 0.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 30 μA IQ at light load (LCM VIN = 12 V and VOUT =3.3 V)
  • 8 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Output voltage adjustable from 0.85 V to VIN
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 360 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

STEVAL-ISA188V1 38 V, 1.5 A synchronous step-down switching regulator evaluation board based on A6986F3V3 Quick view

主要特性

  • AECQ100 qualification
  • 1.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 30 μA IQ at light load (LCM VIN = 12 V)
  • 8 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Fixed output voltage VOUT = 3.3 V
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

STEVAL-ISA190V1 38 V, 1.5 A synchronous step-down switching regulator evaluation board based on A6986F Quick view

主要特性

  • AECQ100 qualification
  • 1.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 30 µA IQ at light load (LCM VIN = 12 V and VOUT = 3.3 V)
  • 8 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Output voltage adjustable from 0.85 V to VIN
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

X-NUCLEO-IKS01A2 Motion MEMS and environmental sensor expansion board for STM32 Nucleo Quick view

主要特性

  • LSM6DSL MEMS 3D accelerometer (±2/±4/±8/±16 g) and 3D gyroscope (±125/±245/±500/±1000/±2000 dps)
  • LSM303AGR MEMS 3D accelerometer (±2/±4/±8/±16 g) and MEMS3D magnetometer (±50 gauss)
  • LPS22HB MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
  • HTS221: capacitive digital relative humidity and temperature
  • DIL24 socket for additional MEMS adapters and other sensors
  • Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
  • I²C sensor hub features on LSM6DSL available
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • RoHS compliant

Show More

X-NUCLEO-NFC04A1 Dynamic NFC/RFID tag IC expansion board based on ST25DV04K for STM32 Nucleo Quick view

主要特性

  • Expansion board based on the ST25DV04K dynamic NFC/RFID tag for STM32 Nucleo
  • Up to 4-Kbit memory with NDEF support
  • 54 mm diameter, single layer circular antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino™ UNO R3 connector
  • Self-powered or powered through the Arduino™ UNO R3 connectors
  • Three general purpose LEDs
  • Scalable solution, capable of cascading multiple boards for larger systems
  • Free comprehensive development firmware library and example for ST25DV04K, compatible with STM32Cube firmware
  • FCC and IC verified
  • RoHS compliant

Show More

ST25DV-DISCOVERY Discovery kit for ST25DV04 Dynamic NFC/RFID tag IC with fast transfer mode capability Quick view

主要特性

  • Two ready-to-use printed circuit boards (PCB):
    • ST25DV_Discovery_Mboard:
    • STM32F405VGT6 LQFP100 32-bit microcontroller, with 1 Mbyte Flash memory, 192 + 4 Kbytes SRAM.
    • LCD color screen (320 x 200 pixels)
    • Touch screen driver
    • Different color LEDs (power, user, ST link)
    • User push button
    • Joystick for menu selection
    • Reset button
    • On board ST link for microcontroller firmware upgrade and debug
    • ST link mini USB
    • User micro USB
    • USB micro or mini connector for board powering
    • Demonstration use cases stored in memory
    • Demonstration edition (optional add-on module) with Bluetooth Low Energy module, Wi-Fi® module and JTAG 20 pin connector
  • ST25DV_Discovery_ANT_C5:
    • 40 mm x 24 mm, 13.56 MHz inductive antenna etched on the PCB
    • ST25DV04K Dynamic NFC / RFID tag
    • I2 C interface connector
    • Energy harvesting output (VOUT) with a 10 nF capacitance filtering circuit
    • GPO configurable as RF WIP/BUSY output, to indicate that an RF operation is ongoing

Show More

ST25R3911B-DISCO Discovery kit for ST25R3911B high performance HF reader / NFC initiator with 1.4 W output power, VHBR and AAT Quick view

主要特性

  • Based on ST25R3911B high performance HF reader / NFC initiator with 1.4 W output power, supporting VHBR and AAT
    • ISO 18092 (NFCIP-1) active P2P
    • ISO14443A, ISO14443B and FeliCa™
    • ISO15693
    • Supports VHBR (3.4 Mbit/s PICC to PCD framing, 6.8 Mbit/s AFE and PCD to PICC framing)
    • Up to 1.4 W output power with differential antenna
    • Possibility of driving two antennas in single ended mode
    • Inductive and capacitive Wake-up
    • Automatic antenna tuning system
    • DPO (Dynamic Power Output)
    • User selectable and automatic gain control
    • Transparent and Stream modes to implement MIFARE™ Classic compliant or other custom protocols
    • 6 Mbit/s SPI
    • Wide supply voltage range (from 2.4 V to 5.5 V)
    • QFN32, 5 mm x 5 mm package
  • STM32L476RET6 32-bit microcontroller with 512 kB of Flash memory
  • 105 mm x 52 mm, two turns antenna etched on the PCB, and associated VHBR tuning circuit
  • Micro-USB connector for communication with the host PC and board powering
  • Six LEDs indicating the presence of the RF field and of the protocol used to communicate

Show More

STEVAL-FKI915V1 Sub-1GHz transceiver development kit based on S2-LP Quick view

主要特性

  • S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier
  • STM32 Nucleo-64 development board with STM32L152RE MCU
  • Suitable for wireless M-Bus systems
  • Suitable for SigFox applications
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +27 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

STEVAL-LDO001V1 Quad high performance LDO evaluation board based on LDBL20, LDLN025, LD39130S and STLQ020 Quick view

主要特性

  • Multi LDO evaluation board based on four high performance low dropout linear voltage regulators in miniature packages
  • Key features:
    • Low operating input voltage (from 1.4 V to 5.5 V)
    • Current capability from 200 mA to 300 mA
    • Low dropout (down to 160 mV typ.)
    • Ultra-low quiescent current (down to 500 nA typ.)
    • Low noise (down to 6.5 μVRMS typ.)
    • High PSSR (up to 80 dB)
    • Logic controlled electronic shutdown (enable)
    • Tiny packages (DFN-6L, Flip-chip, ST STAMP™)
  • RoHS compliant

Show More

ANT-1-6-ST25DV 75 mm x 45 mm and 22.5 mm x 18.5 mm antenna boards package for ST25DV-Discovery kit Quick view

主要特性

  • Ready-to-use printed circuit board (PCB) including:
    • 45 mm x 75 mm (ST25DV_Discovery_ANT_C1) and 18 mm x 24 mm (ST25DV_Discovery_ANT_C6), 13.56 MHz single layer inductive antenna etched on the PCB
    • ST25DV04K dual interface EEPROM
    • Mates with ST25Dx_DISCOVERY_MBOARD connector
    • Energy harvesting output (VOUT ) with a 10 nF capacitance filtering circuit

Show More

图片

Image
Image
STEVAL-MKI179V1 LIS2DW12 adapter board for a standard DIL 24 socket Quick view

主要特性

  • Complete LIS2DW12 pinout for a standard DIL 24 socket
  • Fully compatible with the STEVAL-MKI109V2 and STEVAL-MKI109V3 motherboards
  • RoHS compliant

Show More

图片

Image
Image

特色资源

BOM Gerber
STEVAL-IDB007V2 STEVAL-IDB007V2 evaluation platform based on the BlueNRG-1 Quick view

主要特性

  • Bluetooth® SMART board based on the BlueNRG-1 Bluetooth low energy system on chip
  • Associated BlueNRG-1 development kit SW package including firmware and documentation
  • Up to +8 dBm available output power (at antenna connector)
  • Excellent receiver sensitivity (-88 dBm)
  • Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
  • Bluetooth® low energy compliant, supports master, slave and simultaneous master-and-slave roles
  • New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
  • SMA connector for antenna or measuring equipment
  • 3 user LEDs
  • 2 user buttons
  • 3D digital accelerometer and 3D digital gyroscope
  • MEMS pressure sensor with embedded temperature sensor
  • Battery holder
  • JTAG debug connector
  • USB to serial bridge for providing I/O channel with the BlueNRG-1 device
  • Jumper for measuring current for BlueNRG-1 only
  • RoHS compliant

Show More

STEVAL-IDB008V2 Evaluation platform based on the BlueNRG-2 Quick view

主要特性

  • Bluetooth® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip
  • Associated BlueNRG-2 development kit SW package including firmware and documentation
  • Up to +8 dBm available output power (at antenna connector)
  • Excellent receiver sensitivity (-88 dBm)
  • Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
  • Bluetooth® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature
  • New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
  • SMA connector for antenna or measuring equipment
  • 3 user LEDs
  • 2 user buttons
  • 3D digital accelerometer and 3D digital gyroscope
  • MEMS pressure sensor with embedded temperature sensor
  • RoHS compliant

Show More

STEVAL-SMARTAG1 NFC Dynamic Tag sensor node evaluation board Quick view

主要特性

  • ST25DV64K dynamic NFC tag solution based on 64K-bit (8K-Byte) EEPROM and with I²C interface, Fast Transfer Mode and Energy Harvesting features
  • STM32L031K6 ultra-low-power ARM Cortex-M0+ MCU running at 32 MHz with 32-Kbytes Flash and 8-Kbytes RAM
  • LIS2DW12 ultra-low-power high-performance three-axis linear accelerometer
  • LPS22HB ultra-compact piezo-resistive absolute pressure sensor which functions as a digital output barometer: 260-1260 hPa
  • HTS221 capacitive digital sensor for relative humidity and temperature
  • STLQ015 low drop linear regulator power management
  • CR2032 Battery powered (not included)
  • STM32Cube function pack (FP-SNS-SMARTAG1)
  • Android (Google Play) and iOS demo apps (ST SmarTag)
  • Suitable for the following applications:
    • Internet of Things
    • Supply Chain and Cold-Chain Management
    • Smart building, home and city
    • Retail and apparel
    • Smart packaging
    • Medical and pharmaceutical
    • Batteryless sensing
    • Smart agriculture (soil control, animal tracking, etc.)

Show More

STEVAL-MIC001V1 Microphone coupon board based on the MP34DT05-A digital MEMS Quick view

主要特性

  • 4 x MP34DT05-A top port digital MEMS microphones
  • Daughterboard to be used with X-NUCLEO-CCA02M1
  • Vsupply from 1.6 to 3.6 V
  • 122.5 dBSPL acoustic overload point
  • Omnidirectional sensitivity
  • PDM single-bit output
  • 64 dB of SNR
  • Sensitivity -26 dBFS ±3 dB
  • RoHS compliant

Show More

STEVAL-FKI868V2 Sub-1GHz (860-940 MHz) transceiver development kit based on S2-LP Quick view

主要特性

  • S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands
  • STM32 Nucleo-64 development board with STM32L0 MCU
  • Suitable for Wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX @ +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission, and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

STEVAL-FKI433V2 Sub-1GHz (430-470 MHz) transceiver development kit based on S2-LP Quick view

主要特性

  • S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF module tuned for 430-470 MHz frequency bands
  • STM32 Nucleo-64 development board with STM32L0 MCU
  • Suitable for wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX at +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

X-NUCLEO-IKS01A1 Motion MEMS and environmental sensor expansion board for STM32 Nucleo Quick view

主要特性

  • LSM6DS0: MEMS 3D accelerometer (±2/±4/±8 g) + 3D gyroscope (±245/±500/±2000 dps)
  • LIS3MDL: MEMS 3D magnetometer (±4/ ±8/ ±12/ 16 gauss)
  • LPS25HB*: MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
  • HTS221: capacitive digital relative humidity and temperature
  • DIL 24-pin socket available for additional MEMS adapters and other sensors (UV index)
  • Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • RoHS compliant

Show More

STM32L073Z-EVAL Evaluation board with STM32L073VZ MCU Quick view

主要特性

  • STM32L073VZI6 ultra-low-power Arm® Cortex® core-based microcontroller featuring 192 Kbytes of Flash memory and 20 Kbytes of RAM in LQFP100 package
  • Four 5 V power supply options: power jack, ST-LINK USB connector, user USB FS connector, or daughterboard
  • Selectable MCU voltage: 3.3 V or adjustable from 1.71 V to 3.6 V
  • 2.8-inch color LCD-TFT with resistive touchscreen
  • LCD glass 40 x 8 segments
  • On-board current measurement
  • IrDA transceiver
  • Pressure sensor
  • LC sensor metering
  • Touch sensing linear sensor
  • User and reset push-buttons
  • 4-direction joystick with selection button
  • Board connectors:
    • 2 RS-232 with DB9
    • USB with Micro-B
    • microSD™ card
  • Board expansion connectors:
    • RF-EEPROM daughter board
    • Extension connector for daughter board or wrapping board
  • On-board ST-LINK/V2-1 debugger/ programmer with USB re-enumeration capability: mass storage, virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube package.
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs

Show More

STEVAL-ISA156V1 38 V, 2 A synchronous step-down switching regulator evaluation board based on the L6986 Quick view

主要特性

  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • 30 μA IQ at light load (LCM VOUT = 3.3 V)
  • 5 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Output voltage adjustable from 0.85 V to VIN
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on) HS = 180 mΩ, RDS(on) LS = 110 mΩ
  • Thermal shutdown

Show More

STEVAL-MKI141V2 HTS221 humidity sensor adapter board for standard DIL24 socket (full pinout) Quick view

主要特性

  • Complete HTS221 pinout (SPI & I²C interface) for a standard DIL 24 socket
  • Fully compatible with STEVAL-MKI109V2 motherboard
  • RoHS compliant

Show More

STEVAL-MKI151V1 LIS2DH12 3-axis accelerometer adapter board for standard DIL 24 socket, compatible with STEVAL-MKI109V2 Quick view

主要特性

  • Complete LIS2DH12 pinout for a standard DIL 24 socket
  • Fully compatible with STEVAL-MKI109V2 motherboard
  • RoHS compliant

Show More

NUCLEO-L053R8 STM32 Nucleo-64 development board with STM32L053R8 MCU, supports Arduino and ST morpho connectivity Quick view

主要特性

  • Common features
    • STM32 microcontroller in LQFP64 package
    • 1 user LED shared with Arduino™
    • 1 user and 1 reset push-buttons
    • 32.768 kHz crystal oscillator
    • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
    • Flexible power-supply options: ST-LINK, USB VBUS or external sources
    • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs
  • Board-specific features
    • External SMPS to generate Vcore logic supply
    • 24 MHz HSE
    • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI® debug connector
    • Arm® Mbed Enabled™ compliant

Show More

STEVAL-MKI109V2 eMotion: ST MEMS adapters motherboard based on STM32F103, compatible with all ST MEMS adapter boards Quick view

主要特性

  • Compatible with all available ST MEMS adapter boards
  • Controlled by the STM32F103RET6 high-performance ARM Cortex -M3 microcontroller
  • Includes a DIL24 socket for easy MEMS adapter connection
  • 3 V on-board linear voltage regulator
  • DFU compatible for USB microprocessor firmware update
  • USB 2.0 full-speed compliant
  • Debugging connector for SWD/JTAG
  • RoHS compliant

Show More

产品型号
NUCLEO-L073RZ

STM32 Nucleo-64 development board with STM32L073RZ MCU, supports Arduino and ST morpho connectivity

主要特性

  • Common features
    • STM32 microcontroller in LQFP64 package
    • 1 user LED shared with Arduino™
    • 1 user and 1 reset push-buttons
    • 32.768 kHz crystal oscillator
    • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
    • Flexible power-supply options: ST-LINK, USB VBUS or external sources
    • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs
  • Board-specific features
    • External SMPS to generate Vcore logic supply
    • 24 MHz HSE
    • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI® debug connector
    • Arm® Mbed Enabled™ compliant

Show More

STEVAL-ISB033V1

Evaluation board for STBCFG01 single-cell Li+ battery charger with OTG boost, voltage mode fuel gauge and 200 mA LDO

主要特性

    • 2 MHz or 3 MHz switching frequency
    • 1.2 A max. charging current
    • 20 V tolerant input with OVP
    • Programmable input current limitation and dynamic input current limit
    • Battery overvoltage protection
    • Auto-recharge
    • Integrated current sensing resistor
    • USB compatible
  • Voltage mode fuel gauge
    • External sensing resistor not needed
    • Battery swap detection through ID resistor
    • Low battery voltage and low SOC programmable alarms
  • 50 mA LDO for system boot in dead battery condition
  • USB OTG VBUS generation (500 mA)
    • USB overvoltage protection
    • Programmable battery overcurrent protection
  • Automatic 60 mA input pre-bias
  • I²C compatible control interface
  • Interrupt output pin
  • RoHS compliant

Show More

X-NUCLEO-IDB05A1

Bluetooth Low Energy expansion board based on SPBTLE-RF module for STM32 Nucleo

主要特性

  • STM32 expansion board based on the SPBTLE-RF module for STM32 Nucleo
  • X-NUCLEO-IDB05A1 contains FCC and IC certified module SPBTLE-RF (FCC ID: S9NSPBTLERF and IC: 8976C-SPBTLERF)
  • SPBTLE-RF:
    • Bluetooth Low Energy FCC and IC certified module based on Bluetooth® SMART 4.1 network processor BlueNRG-MS
    • Integrated Balun (BALF-NRG-01D3)
    • Chip antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • Scalable solution, capable of cascading multiple boards for larger systems
  • Free comprehensive development firmware library and example for BlueNRG-MS, compatible with STM32Cube firmware
  • RoHS compliant

Show More

STEVAL-ISA189V1

38 V, 1.5 A synchronous step-down switching regulator evaluation board based on A6986F5V

主要特性

  • AECQ100 qualification
  • 1.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 45 μA IQ at light load (LCM VIN = 12 V)
  • 8 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Fixed output voltage VOUT = 5 V
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

STEVAL-ISA185V1

38 V, 0.5 A synchronous step-down switching regulator evaluation board based on A6985F3V3

主要特性

  • AECQ100 qualification
  • 0.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 30 μA IQ at light load (LCM VIN = 12 V)
  • 8 μA IQ -SHTDWN
  • Adjustable f SW (250 kHz - 2 MHz)
  • Fixed output voltage VOUT = 3.3 V
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 360 mΩ ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

STEVAL-ISA186V1

38 V, 0.5 A synchronous step-down switching regulator evaluation board based on A6985F5V

主要特性

  • AECQ100 qualification
  • 0.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 45 μA IQ at light load (LCM VIN = 12 V)
  • 8 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Fixed output voltage VOUT = 5 V
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 360 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

STEVAL-ISA187V1

38 V, 0.5 A synchronous step-down switching regulator evaluation board based on A6985F

主要特性

  • AECQ100 qualification
  • 0.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 30 μA IQ at light load (LCM VIN = 12 V and VOUT =3.3 V)
  • 8 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Output voltage adjustable from 0.85 V to VIN
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 360 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

STEVAL-ISA188V1

38 V, 1.5 A synchronous step-down switching regulator evaluation board based on A6986F3V3

主要特性

  • AECQ100 qualification
  • 1.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 30 μA IQ at light load (LCM VIN = 12 V)
  • 8 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Fixed output voltage VOUT = 3.3 V
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

STEVAL-ISA190V1

38 V, 1.5 A synchronous step-down switching regulator evaluation board based on A6986F

主要特性

  • AECQ100 qualification
  • 1.5 A DC output current
  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • Programmable ISKIP current
  • 30 µA IQ at light load (LCM VIN = 12 V and VOUT = 3.3 V)
  • 8 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Output voltage adjustable from 0.85 V to VIN
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ
  • Thermal shutdown
  • RoHS compliant

Show More

X-NUCLEO-IKS01A2

Motion MEMS and environmental sensor expansion board for STM32 Nucleo

主要特性

  • LSM6DSL MEMS 3D accelerometer (±2/±4/±8/±16 g) and 3D gyroscope (±125/±245/±500/±1000/±2000 dps)
  • LSM303AGR MEMS 3D accelerometer (±2/±4/±8/±16 g) and MEMS3D magnetometer (±50 gauss)
  • LPS22HB MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
  • HTS221: capacitive digital relative humidity and temperature
  • DIL24 socket for additional MEMS adapters and other sensors
  • Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
  • I²C sensor hub features on LSM6DSL available
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • RoHS compliant

Show More

X-NUCLEO-NFC04A1

Dynamic NFC/RFID tag IC expansion board based on ST25DV04K for STM32 Nucleo

主要特性

  • Expansion board based on the ST25DV04K dynamic NFC/RFID tag for STM32 Nucleo
  • Up to 4-Kbit memory with NDEF support
  • 54 mm diameter, single layer circular antenna
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino™ UNO R3 connector
  • Self-powered or powered through the Arduino™ UNO R3 connectors
  • Three general purpose LEDs
  • Scalable solution, capable of cascading multiple boards for larger systems
  • Free comprehensive development firmware library and example for ST25DV04K, compatible with STM32Cube firmware
  • FCC and IC verified
  • RoHS compliant

Show More

ST25DV-DISCOVERY

Discovery kit for ST25DV04 Dynamic NFC/RFID tag IC with fast transfer mode capability

主要特性

  • Two ready-to-use printed circuit boards (PCB):
    • ST25DV_Discovery_Mboard:
    • STM32F405VGT6 LQFP100 32-bit microcontroller, with 1 Mbyte Flash memory, 192 + 4 Kbytes SRAM.
    • LCD color screen (320 x 200 pixels)
    • Touch screen driver
    • Different color LEDs (power, user, ST link)
    • User push button
    • Joystick for menu selection
    • Reset button
    • On board ST link for microcontroller firmware upgrade and debug
    • ST link mini USB
    • User micro USB
    • USB micro or mini connector for board powering
    • Demonstration use cases stored in memory
    • Demonstration edition (optional add-on module) with Bluetooth Low Energy module, Wi-Fi® module and JTAG 20 pin connector
  • ST25DV_Discovery_ANT_C5:
    • 40 mm x 24 mm, 13.56 MHz inductive antenna etched on the PCB
    • ST25DV04K Dynamic NFC / RFID tag
    • I2 C interface connector
    • Energy harvesting output (VOUT) with a 10 nF capacitance filtering circuit
    • GPO configurable as RF WIP/BUSY output, to indicate that an RF operation is ongoing

Show More

ST25R3911B-DISCO

Discovery kit for ST25R3911B high performance HF reader / NFC initiator with 1.4 W output power, VHBR and AAT

主要特性

  • Based on ST25R3911B high performance HF reader / NFC initiator with 1.4 W output power, supporting VHBR and AAT
    • ISO 18092 (NFCIP-1) active P2P
    • ISO14443A, ISO14443B and FeliCa™
    • ISO15693
    • Supports VHBR (3.4 Mbit/s PICC to PCD framing, 6.8 Mbit/s AFE and PCD to PICC framing)
    • Up to 1.4 W output power with differential antenna
    • Possibility of driving two antennas in single ended mode
    • Inductive and capacitive Wake-up
    • Automatic antenna tuning system
    • DPO (Dynamic Power Output)
    • User selectable and automatic gain control
    • Transparent and Stream modes to implement MIFARE™ Classic compliant or other custom protocols
    • 6 Mbit/s SPI
    • Wide supply voltage range (from 2.4 V to 5.5 V)
    • QFN32, 5 mm x 5 mm package
  • STM32L476RET6 32-bit microcontroller with 512 kB of Flash memory
  • 105 mm x 52 mm, two turns antenna etched on the PCB, and associated VHBR tuning circuit
  • Micro-USB connector for communication with the host PC and board powering
  • Six LEDs indicating the presence of the RF field and of the protocol used to communicate

Show More

STEVAL-FKI915V1

Sub-1GHz transceiver development kit based on S2-LP

主要特性

  • S2-LP narrow band ultra-low power Sub-1GHz transceiver in a standalone RF module tuned for 860-940 MHz frequency bands with external power amplifier
  • STM32 Nucleo-64 development board with STM32L152RE MCU
  • Suitable for wireless M-Bus systems
  • Suitable for SigFox applications
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +27 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

STEVAL-LDO001V1

Quad high performance LDO evaluation board based on LDBL20, LDLN025, LD39130S and STLQ020

主要特性

  • Multi LDO evaluation board based on four high performance low dropout linear voltage regulators in miniature packages
  • Key features:
    • Low operating input voltage (from 1.4 V to 5.5 V)
    • Current capability from 200 mA to 300 mA
    • Low dropout (down to 160 mV typ.)
    • Ultra-low quiescent current (down to 500 nA typ.)
    • Low noise (down to 6.5 μVRMS typ.)
    • High PSSR (up to 80 dB)
    • Logic controlled electronic shutdown (enable)
    • Tiny packages (DFN-6L, Flip-chip, ST STAMP™)
  • RoHS compliant

Show More

ANT-1-6-ST25DV

75 mm x 45 mm and 22.5 mm x 18.5 mm antenna boards package for ST25DV-Discovery kit

主要特性

  • Ready-to-use printed circuit board (PCB) including:
    • 45 mm x 75 mm (ST25DV_Discovery_ANT_C1) and 18 mm x 24 mm (ST25DV_Discovery_ANT_C6), 13.56 MHz single layer inductive antenna etched on the PCB
    • ST25DV04K dual interface EEPROM
    • Mates with ST25Dx_DISCOVERY_MBOARD connector
    • Energy harvesting output (VOUT ) with a 10 nF capacitance filtering circuit

Show More

图片

Image
Image
STEVAL-MKI179V1

LIS2DW12 adapter board for a standard DIL 24 socket

主要特性

  • Complete LIS2DW12 pinout for a standard DIL 24 socket
  • Fully compatible with the STEVAL-MKI109V2 and STEVAL-MKI109V3 motherboards
  • RoHS compliant

Show More

图片

Image
Image

特色资源

BOM Gerber
STEVAL-IDB007V2

STEVAL-IDB007V2 evaluation platform based on the BlueNRG-1

主要特性

  • Bluetooth® SMART board based on the BlueNRG-1 Bluetooth low energy system on chip
  • Associated BlueNRG-1 development kit SW package including firmware and documentation
  • Up to +8 dBm available output power (at antenna connector)
  • Excellent receiver sensitivity (-88 dBm)
  • Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
  • Bluetooth® low energy compliant, supports master, slave and simultaneous master-and-slave roles
  • New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
  • SMA connector for antenna or measuring equipment
  • 3 user LEDs
  • 2 user buttons
  • 3D digital accelerometer and 3D digital gyroscope
  • MEMS pressure sensor with embedded temperature sensor
  • Battery holder
  • JTAG debug connector
  • USB to serial bridge for providing I/O channel with the BlueNRG-1 device
  • Jumper for measuring current for BlueNRG-1 only
  • RoHS compliant

Show More

STEVAL-IDB008V2

Evaluation platform based on the BlueNRG-2

主要特性

  • Bluetooth® SMART board based on the BlueNRG-2 Bluetooth low energy system on chip
  • Associated BlueNRG-2 development kit SW package including firmware and documentation
  • Up to +8 dBm available output power (at antenna connector)
  • Excellent receiver sensitivity (-88 dBm)
  • Very low power consumption: 7.7 mA RX and 8.2 mA TX at +0 dBm
  • Bluetooth® SMART v5.0 compliant, supports master, slave, simultaneous master-and-slave roles and Bluetooth low energy extended data length feature
  • New integrated balun BALF-NRG-02D3 which integrates a matching network and harmonics filter
  • SMA connector for antenna or measuring equipment
  • 3 user LEDs
  • 2 user buttons
  • 3D digital accelerometer and 3D digital gyroscope
  • MEMS pressure sensor with embedded temperature sensor
  • RoHS compliant

Show More

STEVAL-SMARTAG1

NFC Dynamic Tag sensor node evaluation board

主要特性

  • ST25DV64K dynamic NFC tag solution based on 64K-bit (8K-Byte) EEPROM and with I²C interface, Fast Transfer Mode and Energy Harvesting features
  • STM32L031K6 ultra-low-power ARM Cortex-M0+ MCU running at 32 MHz with 32-Kbytes Flash and 8-Kbytes RAM
  • LIS2DW12 ultra-low-power high-performance three-axis linear accelerometer
  • LPS22HB ultra-compact piezo-resistive absolute pressure sensor which functions as a digital output barometer: 260-1260 hPa
  • HTS221 capacitive digital sensor for relative humidity and temperature
  • STLQ015 low drop linear regulator power management
  • CR2032 Battery powered (not included)
  • STM32Cube function pack (FP-SNS-SMARTAG1)
  • Android (Google Play) and iOS demo apps (ST SmarTag)
  • Suitable for the following applications:
    • Internet of Things
    • Supply Chain and Cold-Chain Management
    • Smart building, home and city
    • Retail and apparel
    • Smart packaging
    • Medical and pharmaceutical
    • Batteryless sensing
    • Smart agriculture (soil control, animal tracking, etc.)

Show More

STEVAL-MIC001V1

Microphone coupon board based on the MP34DT05-A digital MEMS

主要特性

  • 4 x MP34DT05-A top port digital MEMS microphones
  • Daughterboard to be used with X-NUCLEO-CCA02M1
  • Vsupply from 1.6 to 3.6 V
  • 122.5 dBSPL acoustic overload point
  • Omnidirectional sensitivity
  • PDM single-bit output
  • 64 dB of SNR
  • Sensitivity -26 dBFS ±3 dB
  • RoHS compliant

Show More

STEVAL-FKI868V2

Sub-1GHz (860-940 MHz) transceiver development kit based on S2-LP

主要特性

  • S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF Module tuned for 860-940 MHz frequency bands
  • STM32 Nucleo-64 development board with STM32L0 MCU
  • Suitable for Wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX @ +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission, and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

STEVAL-FKI433V2

Sub-1GHz (430-470 MHz) transceiver development kit based on S2-LP

主要特性

  • S2-LP narrow band ultra-low power sub-1GHz transceiver in a standalone RF module tuned for 430-470 MHz frequency bands
  • STM32 Nucleo-64 development board with STM32L0 MCU
  • Suitable for wireless M-Bus systems
  • Associated S2-LP development kit including, documentation, firmware for STM32L and GUI
  • Programmable RF output power up to +16 dBm
  • Modulation schemes: 2-FSK, 2-GFSK, 4-FSK, 4-GFSK, OOK, and ASK
  • Air data rate from 0.3 to 500 kbps
  • Ultra-low power consumption:
    • 6.7 mA RX
    • 10 mA TX at +10 dBm
  • Excellent performance of receiver sensitivity (up to -130 dBm)
  • Low duty cycle RX/TX operation mode
  • Automatic acknowledgement, retransmission and timeout protocol engine
  • SPI interface for microcontroller
  • USB interface
  • RoHS compliant

Show More

X-NUCLEO-IKS01A1

Motion MEMS and environmental sensor expansion board for STM32 Nucleo

主要特性

  • LSM6DS0: MEMS 3D accelerometer (±2/±4/±8 g) + 3D gyroscope (±245/±500/±2000 dps)
  • LIS3MDL: MEMS 3D magnetometer (±4/ ±8/ ±12/ 16 gauss)
  • LPS25HB*: MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
  • HTS221: capacitive digital relative humidity and temperature
  • DIL 24-pin socket available for additional MEMS adapters and other sensors (UV index)
  • Free comprehensive development firmware library and example for all sensors compatible with STM32Cube firmware
  • Compatible with STM32 Nucleo boards
  • Equipped with Arduino UNO R3 connector
  • RoHS compliant

Show More

STM32L073Z-EVAL

Evaluation board with STM32L073VZ MCU

主要特性

  • STM32L073VZI6 ultra-low-power Arm® Cortex® core-based microcontroller featuring 192 Kbytes of Flash memory and 20 Kbytes of RAM in LQFP100 package
  • Four 5 V power supply options: power jack, ST-LINK USB connector, user USB FS connector, or daughterboard
  • Selectable MCU voltage: 3.3 V or adjustable from 1.71 V to 3.6 V
  • 2.8-inch color LCD-TFT with resistive touchscreen
  • LCD glass 40 x 8 segments
  • On-board current measurement
  • IrDA transceiver
  • Pressure sensor
  • LC sensor metering
  • Touch sensing linear sensor
  • User and reset push-buttons
  • 4-direction joystick with selection button
  • Board connectors:
    • 2 RS-232 with DB9
    • USB with Micro-B
    • microSD™ card
  • Board expansion connectors:
    • RF-EEPROM daughter board
    • Extension connector for daughter board or wrapping board
  • On-board ST-LINK/V2-1 debugger/ programmer with USB re-enumeration capability: mass storage, virtual COM port and debug port
  • Comprehensive free software libraries and examples available with the STM32Cube package.
  • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs

Show More

STEVAL-ISA156V1

38 V, 2 A synchronous step-down switching regulator evaluation board based on the L6986

主要特性

  • 4 V to 38 V operating input voltage
  • Low consumption mode or low noise mode
  • 30 μA IQ at light load (LCM VOUT = 3.3 V)
  • 5 μA IQ-SHTDWN
  • Adjustable fSW (250 kHz - 2 MHz)
  • Output voltage adjustable from 0.85 V to VIN
  • Embedded output voltage supervisor
  • Synchronization
  • Adjustable soft-start time
  • Internal current limiting
  • Overvoltage protection
  • Output voltage sequencing
  • Peak current mode architecture
  • RDS(on) HS = 180 mΩ, RDS(on) LS = 110 mΩ
  • Thermal shutdown

Show More

STEVAL-MKI141V2

HTS221 humidity sensor adapter board for standard DIL24 socket (full pinout)

主要特性

  • Complete HTS221 pinout (SPI & I²C interface) for a standard DIL 24 socket
  • Fully compatible with STEVAL-MKI109V2 motherboard
  • RoHS compliant

Show More

STEVAL-MKI151V1

LIS2DH12 3-axis accelerometer adapter board for standard DIL 24 socket, compatible with STEVAL-MKI109V2

主要特性

  • Complete LIS2DH12 pinout for a standard DIL 24 socket
  • Fully compatible with STEVAL-MKI109V2 motherboard
  • RoHS compliant

Show More

NUCLEO-L053R8

STM32 Nucleo-64 development board with STM32L053R8 MCU, supports Arduino and ST morpho connectivity

主要特性

  • Common features
    • STM32 microcontroller in LQFP64 package
    • 1 user LED shared with Arduino™
    • 1 user and 1 reset push-buttons
    • 32.768 kHz crystal oscillator
    • Board connectors:Arduino™ Uno V3 expansion connectorST morpho extension pin headers for full access to all STM32 I/Os
    • Flexible power-supply options: ST-LINK, USB VBUS or external sources
    • On-board ST-LINK debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port and debug port
    • Comprehensive free software libraries and examples available with the STM32Cube MCU Package
    • Support of a wide choice of Integrated Development Environments (IDEs) including IAR™, Keil® and GCC-based IDEs
  • Board-specific features
    • External SMPS to generate Vcore logic supply
    • 24 MHz HSE
    • Board connectors:External SMPS experimentation dedicated connectorMicro-AB or Mini-AB USB connector for the ST-LINKMIPI® debug connector
    • Arm® Mbed Enabled™ compliant

Show More

STEVAL-MKI109V2

eMotion: ST MEMS adapters motherboard based on STM32F103, compatible with all ST MEMS adapter boards

主要特性

  • Compatible with all available ST MEMS adapter boards
  • Controlled by the STM32F103RET6 high-performance ARM Cortex -M3 microcontroller
  • Includes a DIL24 socket for easy MEMS adapter connection
  • 3 V on-board linear voltage regulator
  • DFU compatible for USB microprocessor firmware update
  • USB 2.0 full-speed compliant
  • Debugging connector for SWD/JTAG
  • RoHS compliant

Show More

00 选择要下载的文档

技术文档

    • 描述 版本 文档大小 操作
      AN5085
      Cycling endurance and data retention of EEPROMs in ST25DVxxx products based on CMOS F8H process
      2.0
      306.83 KB
      PDF
      AN4910
      Data exchange between wired (I²C) and wireless (RF ISO 15693) using fast transfer mode supported by ST25DV-I2C
      2.0
      598.03 KB
      PDF
      AN2972
      How to design an antenna for dynamic NFC tags
      9.0
      1.59 MB
      PDF
      AN5038
      LIS2DW12:始终开启的3D 加速度计
      1.0
      3 MB
      PDF
      AN4911
      NDEF management with ST25DVxxx and ST25TVxxx products
      4.0
      460.67 KB
      PDF
      AN5085

      Cycling endurance and data retention of EEPROMs in ST25DVxxx products based on CMOS F8H process

      AN4910

      Data exchange between wired (I²C) and wireless (RF ISO 15693) using fast transfer mode supported by ST25DV-I2C

      AN2972

      How to design an antenna for dynamic NFC tags

      AN5038

      LIS2DW12:始终开启的3D 加速度计

      AN4911

      NDEF management with ST25DVxxx and ST25TVxxx products

    • 描述 版本 文档大小 操作
      TN0018
      LGA 封装中MEMS 传感器的表面贴装指南
      1.0
      251.2 KB
      PDF
      TN0018

      LGA 封装中MEMS 传感器的表面贴装指南

    • 描述 版本 文档大小 操作
      DT0053
      6-point tumble sensor calibration
      1.0
      464.9 KB
      PDF
      DT0053

      6-point tumble sensor calibration

演示和培训资料

    • 描述 版本 文档大小 操作
      Discover the STM32 with a free 32-bit Cortex-M0/0+ MCU Professional Developer’s Package: Webinar Presentation 1.0
      4.28 MB
      PDF
      ST25TV NFC tags Product Presentation 1.0
      1.6 MB
      PDF
      STM32 Development Boards Portfolio 1.2
      2.98 MB
      PDF
      STM32 and STM8 embedded software solutions 7.0
      3.12 MB
      PDF

      Discover the STM32 with a free 32-bit Cortex-M0/0+ MCU Professional Developer’s Package: Webinar Presentation

      ST25TV NFC tags Product Presentation

      STM32 Development Boards Portfolio

      STM32 and STM8 embedded software solutions

出版刊物和宣传资料

    • 描述 版本 文档大小 操作
      ST25DV系列动态NFC/RFID标签 ISO/IEC 15693 NFC Forum Type 5 1.1
      265.36 KB
      PDF

      ST25DV系列动态NFC/RFID标签 ISO/IEC 15693 NFC Forum Type 5

    • 描述 版本 文档大小 操作
      NFC solutions from ST 1.0
      5.1 MB
      PDF
      STM32L0 Series - Ultra-low-power MCUs - Tailored to your needs 17.03
      1.95 MB
      PDF

      NFC solutions from ST

      STM32L0 Series - Ultra-low-power MCUs - Tailored to your needs

开发工具硬件

    • 产品型号

      STM32Cube initialization code generator

软件

    • 产品型号

      Bluetooth Low Energy and Dynamic NFC tag software expansion for STM32Cube

      STM32Cube function pack for IoT node with Dynamic NFC Tag, environmental and motion sensors

      Bluetooth Low Energy software expansion for STM32Cube

      Sensor and DSP algorithm software expansion for STM32Cube

      Sensor and motion algorithm software expansion for STM32Cube

      Dynamic NFC/RFID tag IC software expansion for STM32Cube

    • 产品型号

      Android sensor HAL for MEMS motion and environmental sensors (Industrial I/O framework)

      Android sensor HAL for MEMS motion and environmental sensors (Input framework)

      Standard C platform-independent drivers for MEMS motion and environmental sensors

      Linux device drivers for MEMS motion and environmental sensors (Industrial I/O framework)

      Linux device drivers for MEMS motion and environmental sensors (Input framework)

    • 产品型号

      Application executable of the "NFC Tap" Android app for ST25 product family

      Firmware for ST25DV-DISCOVERY kit

      Application executable of the "NFC Tap" iOS app for ST25 product family

      Software Development Kit for ST25 Tags and Dynamic Tags

Audio ICs

产品型号 描述
MP34DT05-A MEMS audio sensor omnidirectional digital microphone, 64 dB SNR, -26 dBFS sensitivity, top-port, 122.5 dBSPL AOP
产品型号
MEMS audio sensor omnidirectional digital microphone, 64 dB SNR, -26 dBFS sensitivity, top-port, 122.5 dBSPL AOP

Interfaces and Transceivers

产品型号 描述
STUSBCD01B USB charger detection interface
产品型号
USB charger detection interface

MEMS and Sensors

产品型号 描述
LIS2DW12 3-axis MEMS accelerometer, ultra low power, configurable single/double-tap recognition, free-fall, wakeup, portrait/landscape, 6D/4D orientation detections
STLM20 Analog temperature sensor, ultra-low current 2.4 V, high precision
STTS751 2.25 V low-voltage local digital temperature sensor
产品型号
3-axis MEMS accelerometer, ultra low power, configurable single/double-tap recognition, free-fall, wakeup, portrait/landscape, 6D/4D orientation detections
Analog temperature sensor, ultra-low current 2.4 V, high precision
2.25 V low-voltage local digital temperature sensor

电源管理

产品型号 描述
LD39050 500 mA low quiescent current and low noise voltage regulator
LD39100 1 A low quiescent current low noise voltage regulator
LD39130S 300 mA very low quiescent current Linear regulator IC with automatic Green mode
LD39200 2 A high PSRR ultra low drop linear regulator with reverse current protection
LDK120 200 mA low quiescent current very low noise LDO
LDK130 300 mA low quiescent current very low noise LDO
STBC02 Li-Ion linear battery charger with LDO, load switches and reset generator
STBC03 Li-Ion linear battery charger with LDO and load switches
STBC08 800mA STANDALONE LINEAR Li-Ion Battery charger with thermal regulation
STC4054 800mA Standalone linear Li-Ion battery charger with thermal regulation
STLQ020 200 mA ultra-low quiescent current LDO
STNS01 Li-Ion Linear Battery Charger with LDO
产品型号
500 mA low quiescent current and low noise voltage regulator
1 A low quiescent current low noise voltage regulator
300 mA very low quiescent current Linear regulator IC with automatic Green mode
2 A high PSRR ultra low drop linear regulator with reverse current protection
200 mA low quiescent current very low noise LDO
300 mA low quiescent current very low noise LDO
Li-Ion linear battery charger with LDO, load switches and reset generator
Li-Ion linear battery charger with LDO and load switches
800mA STANDALONE LINEAR Li-Ion Battery charger with thermal regulation
800mA Standalone linear Li-Ion battery charger with thermal regulation
200 mA ultra-low quiescent current LDO
Li-Ion Linear Battery Charger with LDO

Switches and Multiplexers

产品型号 描述
STCC2540 USB charging controller with integrated power switch
产品型号
USB charging controller with integrated power switch

无线收发器、MCU、模块

产品型号 描述
BlueNRG-1 Bluetooth Low Energy System On Chip
BlueNRG-MS Bluetooth Low Energy Network Processor supporting Bluetooth 4.2 core specification
S2-LP Ultra-low power, high performance, sub-1GHz transceiver
SPBTLE-1S Very low power application module for Bluetooth® Smart v4.2
SPBTLE-RF Very low power module for Bluetooth Smart v4.1
产品型号
Bluetooth Low Energy System On Chip
Bluetooth Low Energy Network Processor supporting Bluetooth 4.2 core specification
Ultra-low power, high performance, sub-1GHz transceiver
Very low power application module for Bluetooth® Smart v4.2
Very low power module for Bluetooth Smart v4.1
支持中心或 提供反馈