智能天线

主要特性

• ST Teseo III GNSS platform;
• Multiconstellation GNSS: GPS, Galileo, Glonass, Beidou, QZSS are supported;
• USB Power Supply and battery charge;
• Internal battery for standalone usage;
• ON/OFF and Reset buttons available;
• NMEA over:
  • Bluetooth;
  • UART by USB;
  • USB;
• μSD/MMC card reader for easy logging;
• ST 3 axis gyroscope, ST 3 axis accelerometer and ST pressure sensor to enable ST Teseo DRAW1;
• PPS output;
• Leds:
  • PPS
  • Fix status
  • Antenna sensing
  • Power

Show More

主要特性

• Includes the EMIF02-01OABRY highly integrated solution designed to suppress EMI noise and protect against ESD
• Attenuation profile compliant with BroadR Reach™ requirements, from - 40 °C to 125 °C
• Compliant with ISO10605, ISO7637-3 standards
• RoHS compliant

Show More

主要特性

• Input voltage 5 V
• 12 V output, step-up converter for transceiver supply voltage
• LIN transceiver
• CAN transceiver
• Automotive-grade ESD protection
• IEC61000-4-2 compatibility

Show More

主要特性

• Compatible with all available ST MEMS adapter boards
• Controlled by the STM32F401VE high-performance ARM Cortex™ - M4 microcontroller
• Software-adjustable power circuitry to set sensor supply voltage from 0 to 3.6 V
• Includes a DIL24 socket for easy MEMS adapter connection
• Adjustable MEMS DIL24 power supply
• DFU-compatible for USB microprocessor firmware update
• USB 2.0 full-speed compliant
• Embedded power monitoring circuitry on sensor supply voltage and current
• Debugging connector for SWD/JTAG
• Can be used with PC software like Unico GUI to manage and analyze MEMS sensor data
• RoHS compliant

Show More

主要特性

• DC-DC1 working at 1.2 V, 2 MHz
• DC-DC2 working at 5 V, 250 kHz
• Input connector to sync a different working frequency up to 2MHz
• Oscillator on board to change working frequency up to 2MHz
• DC-DC1 and DC-DC2 working up to 3A
• LDO working at 3.3 V, 250 mA
• Possibility to change output voltages
• Jumpers to enable or disable DC-DC
• Jumpers to enable or disable LDO
• Pins to independently supply DC-DC1 and DC-DC2 together with LDO
• Output connectors to check output voltages

Show More

主要特性

• Complete AIS328DQ pinout for a standard DIL 24 socket
• Fully compatible with the STEVAL-MKI109V2 motherboard
• RoHS compliant

Show More

主要特性

• Compatible with all available ST MEMS adapter boards
• Controlled by the STM32F103RET6 high-performance ARM Cortex^™ -M3 microcontroller
• Includes a DIL24 socket for easy MEMS adapter connection
• 3 V on-board linear voltage regulator
• DFU compatible for USB microprocessor firmware update
• USB 2.0 full-speed compliant
• Debugging connector for SWD/JTAG
• RoHS compliant

Show More

主要特性

• Complete A3G4250D pinout for a standard DIL 24 socket
• Fully compatible with the STEVAL-MKI109V2 motherboard
• RoHS compliant

Show More

主要特性

• Supports both SPC5-UDESTK standalone and the equivalent version embedded into Discovery board.
• Supports SPC5x MCUs
• Supports Multicore, eTPU and GTM debugging
• Includes FLASH programming capability
• Support service provided through STMicroelectronics

Show More

主要特性

• Complete AIS3624DQ pin-out for a standard DIL24 socket
• Fully compatible with STEVAL-MKI109V2 motherboard
• RoHS compliant

Show More

主要特性

• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• 30 µA I_Q at light load (LCM V_OUT = 3.3 V)
• 5 µA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Output voltage adjustable from 0.85 V to V_IN
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

Show More

主要特性

• AECQ100 qualification
• 1.5 A DC output current
• 4 V to 38 V operating input voltage
• Low consumption mode or low noise mode
• Programmable I_SKIP current
• 30 μA I_Q at light load (LCM V_IN = 12 V)
• 8 μA I_Q-SHTDWN
• Adjustable f_SW (250 kHz - 2 MHz)
• Fixed output voltage V_OUT = 3.3 V
• Embedded output voltage supervisor
• Synchronization
• Adjustable soft-start time
• Internal current limiting
• Overvoltage protection
• Output voltage sequencing
• Peak current mode architecture
• R_DS(on)HS = 180 mΩ; R_DS(on)LS = 150 mΩ
• Thermal shutdown
• RoHS compliant

Show More

主要特性

• DC-DC1 working at 1.2 V, 2 MHz
• DC-DC2 working at 5 V, 250 kHz
• Input connector to sync a different working frequency up to 2MHz
• Oscillator on board to change working frequency up to 2MHz
• DC-DC1 and DC-DC2 working up to 3A
• LDO working at 3.3 V, 250 mA
• Possibility to change output voltages
• Jumpers to enable or disable DC-DC
• Jumpers to enable or disable LDO
• Pins to independently supply DC-DC1 and DC-DC2 together with LDO
• Output connectors to check output voltages

Show More